Enter your postal code to find your store Switch to Map View The item was added to your wish list. View my Wish List CycleGear got an upgrade. Tell us what you like, what's missing, or what's broken.3 ClockwiseClockwise DirectionCounter ClockwiseHead MicrometerMicrometer TorqueRatcheting HeadDrive RatchetingIndustrial TorqueStandard IndustrialForwardStanley Proto J6008C 1/2-Inch Drive Ratcheting Head Micrometer Torque Wrench, 16-80-Feet Pound Calibrated to +/- 3% clockwise direction and +/- 6% counter clockwise at 20% to 100% of full scale. Calibration is accomplished by manual loading the torque wrenches. Manufactured to meet standard industrial torque applications, general industry, heavy equipment and maintenance. SAFETY FIRST: Protective gloves and eyewear are recommended at this point. There are two different types of spokes used on most spoke wheels. The inner spokes run on the inside of the hub flange and have a 90 degree bend to them. The outer spokes run on the outer side of the hub flange and are less than 90 degrees.

Install one inner spoke with a piece of tape on it in the lower flange first, followed by an inner spoke in the upper flange with a piece of tape on it. Make sure the lower spoke is in front of the upper spoke. Install eight more inner spokes down through the hub’s upper flange leaving a open spoke hole between each one. Make sure the spokes are pointing in a counter clockwise direction. Install eight more inner spokes up through the lower hub flange.  Position these spokes in a clockwise direction. All the inner spokes must be installed into the hub before the rim can be installed. Place the rim over the hub and inner spokes and lace the upper taped spoke to the first spoke hole to the right of the valve stem hole. Screw a nipple on to the spoke about three turns. Make sure this spoke is in its correct location or the wheel will not be laced properly. Install the rest of the inner spokes on the upper hub to the rim leaving every fourth hole open.

Once the inner spokes are in and the their nipples are on loosely, twist the hub in a clockwise direction while holding the rim to locate the spokes in their correct location. Holding the rim and hub, turn the wheel over and lace the taped lower spoke to the seventh hole counter-clockwise from the first taped spoke, install a nipple.motorcycle dealers cairo egypt This spoke will face the opposite direction of the already installed spokes.kawasaki vulcan for sale on ebay Install the remaining spokes to the lower hub flange and install their nipples. motorcycle parts youngstown ohioThe wheel should look like two stars when laced correctly.lightweight 3/4 motorcycle helmets

Install the nine outer spokes in the lower flange hub in a counter-clockwise direction. Install the next nine outer spokes in the upper flange hub and connect them to the remaining rim holes and install their nipples. Tighten all the nipples evenly so that only a few threads show on the spoke. With the spokes snug, place the wheel into a wheel truing stand. With a magnetic stand and a dial indicator in position, spin the wheel and measure the amount of runout. If the wheel moves side to side that is known as lateral wobble, if the wheel moves up and down that is known as radial hop. When truing a wheel always correct the radial hop before correcting the lateral wobble. To correct radial hop loosen the inside and outside spokes directly opposite of the high spot. Locate the high spot on the rim and tighten the nipples 1/4 of a turn at a time until the high spot fades. To correct lateral rim wobble you will need to figure out if its the right or left side first.

If the right side is out you will need to loosen several spokes on the right side where the wobble is and spin the wheel to see if this helped. If so tighten the spokes evenly and recheck. If the wheel still wobbles tighten several spokes near the wobble on the left side at the high point. Using a spoke wrench, check the tightness of each spoke. When replacing the tire or tube remove the rim strap and inspect each nipple and lubricate them with a penetrating oil to keep them from corroding. Replace the spokes or nipples as needed. Spoke nipple torque wrenches are available from most motorcycle dealerships and parts suppliers. Tighten all the spokes evenly to the specified torque.This is a "machine-selection optional" part.Please choose a vehicle to see products specific to your machine, select a product below.Choose a vehicle:Machine Type: User Tip: If you're unsure of your vehicle type, you may skip the machine type selection box.» Log in to use your Rider Profile Machines Items 1 – 52 of 112 |

View Compare Quick View Compare Quick View Compare Quick View Compare Quick View Compare Quick View Compare Quick View Compare Quick View Compare Quick View Compare Quick View Compare Quick View Compare Quick View Compare Quick View Compare Quick View Compare Quick View Compare Quick View Compare Quick View Compare Quick ViewWATCH VIDEO Compare Quick View Compare Quick View Compare Quick View Compare Quick View Compare Quick View Compare Quick View Compare Quick View Compare Quick View Compare Quick View Compare Quick View Compare Quick View Compare Quick View Compare Quick View Compare Quick ViewWATCH VIDEO Compare Quick View Compare Quick View Compare Quick View Compare Quick View Compare Quick View Compare Quick View Compare Quick View Compare Quick View Compare Quick View Compare Quick View Compare Quick View Compare Quick View Compare Quick View Compare Quick View Compare Quick View Compare Quick View Compare Quick ViewWATCH VIDEO Compare Quick View Compare Quick View Compare Quick View Compare Quick View

Items 1 – 52 of 112 | View Motorcycle Tire and Wheel Tools at Jake WilsonJake Wilson carries the biggest variety of tire tools and accessories to help you get everything you need to be able to work on your motorcycle from your own shop or garage. We have a large selection including levers, axle tools, tire gauges, inflators, tire irons and more from top industry brands like Motion Pro, Tusk and Excel. .Latest Accessories Tire/Wheel Tools Reviews – You could win up to for reviewing products!Tusk Spoke Wrench Setdylan in TXNot bad but I wish it was all Metal -m-2005 HONDA CRF450R--Read All ReviewsTusk Racer Axle WrenchGriffin in CANice wrenchIt's a little short so lacking leverage but I was able to take my bike apart with it and I used it to put it back together to make sure I don't over tighten it for next time. I bought to keep in my backpack.Read All ReviewsMotion Pro Bead Buddy II Motorcycle Tire ToolGriffin in CANot necessary but...Not necessary at all but I bought one because I kept looking at it.